Search Results

This paper first traces the early development of aviation engines in various countries. The six-cylinder Mercedes, V-type twelve-cylinder Renault, and six-cylinder Benz engines are then described in detail and illustrated. Various types of Sunbeam, Curtiss, and Austro-Daimler are also described. The effect of offset crankshafts, as employed on the Benz and Austro-Daimler engines, is illustrated by pressure and inertia diagrams and by textual description. The paper concludes with a section on the requirements as to size of aviation engines, four curves showing the changing conditions which affect the engine size requirements. These curves relate to variations of temperature, air density, engine speed, airplane speed and compression ratio required to compensate for decrease in air density, all as related to varying altitude.

Inasmuch as horses cannot meet the demand for increased farm power, the tractor must come at once. So far the supply of tractors has been entirely inadequate to meet the demand. The author specifiies some of the problems that confront designers of farm tractors. To make the tractor immediately available for farm work, it must be adaptable to practically all of the existing types of horse-drawn implements, besides furnishing belt power for a wide variety of present power-driven farm machinery. In designing tractors it must be remembered that the horse is a very flexible unit, capable of a wide variation in power output. Designing a tractor to furnish the necessary power for the majority of farm conditions, requires an intimate knowledge of crops, soils and farm management. These must be analyzed carefully so as to make the machine have as wide a range of usefulness as possible.

The authors first define the elementary conditions governing combustion efficiency, dividing these conditions into three main classes. They next compare engines operating on constant volume, constant temperature and constant pressure cycles, dealing specifically with the Otto, Diesel and semi-Diesel types. The main part of the paper is devoted to an outline of the constant pressure cycle, analyzing its advantages as compared with the merits of the constant volume cycle now used in internal-combustion engines. The paper is concluded with a detail description of a proposed constant pressure engine.

Predictable and unpredictable forces will change the direction of the charge-air systems industry. The driver of diesel engine development will be the stringent emissions regulations of the 1990s. The drivers in the gasoline engine market will be improved fuel economy, performance, durability and emissions. Forces will also influence the charge-air marketplace, including changes in emission standards, national fiscal policies, political issues, fuel prices, alternate fuels and consumer tastes. The world community mandate for engines that are clean, quiet, durable and fuel efficient will be satisfied, increasingly, by first-tier component suppliers developing integrated systems solutions.

Many areas of the world are in various stages of development which frequently includes a rapid increase in the motor vehicle population. As a result, some areas are beginning to show the effect of increased motor vehicle use on air pollution. The vehicle's contribution to California's air pollution has long been recognized and studied, and measures have been implemented to reduce emissions from motor vehicles. The history of light duty vehicle emission control in the South Coast Air Basin of California is reviewed. Emission reductions achieved, current levels, projected future emissions and the need for further emissions reductions from light duty vehicles are discussed. For other areas of the world where motor vehicles contribute to air pollution, suggestions are made which can improve the effectiveness of emission control efforts; which should be consistent with political and economic realities, and efforts to achieve international harmonization of standards.

To improve the cold startability of methanol, methanol-butane mixed fuel was experimented. Engine performance and exhaust emissions are obtained with methanol-butane mixed fuel. These characteristics are compared with those of methanol and gasoline. The mixing ratios of methanol and butane are 50:50 (M50), 80:20 (M80), and 90:10 (M90) based on the calorific value. As a result, M90 produces more power than gasoline and more or less than methanol depending on the engine speed and the excess air ratio. Brake horse power of M90 is higher than that of gasoline by 5 - 10 %, and brake specific fuel consumption is smaller than that of gasoline by 17 % to the maximum based on the calorific value. NOx emission concentrations for M90 are lower than those for gasoline and higher than those for methanol because of the effect of butane, CO emission concentrations are somewhat lower than those for methanol and gasoline.

In order to achieve lean burn engine control system, it is necessary to develop high accuracy air fuel ratio control technology including transient driving condition and lean burn limit expansion technology. This paper describes the following. 1 The characteristics of the transient response of the fuel supply are clarified when various kinds of air flow measuring methods and fuel injection methods are used. 2 To achieve stable combustion in lean mixture, fine fuel droplet mixture, whose diameter is less than 40 μm, needs to be supplied.

A procedure has been developed for evaluating equivalent drive cycle emission results from raw exhaust gas emissions data obtained from an engine under test on a computer controlled Vehicle Simulator Engine Dynamometer. The emitted species data is integrated with the air intake flow rate to determine the total mass of emissions, after correcting for the reduction in exhaust gas mass due to precipitation of the moisture of combustion. This procedure eliminates the need for the Constant Volume Sample (CVS) System attached to the vehicle exhaust while undergoing simulated drive testing on a chassis dynamometer to evaluate compliance of the test vehicle with the Australian Design Rules, ADR27 and ADR37. Sources of error with the procedure are examined by comparing the fuel consumption measured using a volumetric technique during the test with that evaluated by a carbon balance procedure as given in the Australian Design Rules.

An all-ceramic swirl chamber has been developed and analyses and evaluations concerning the strength of silicon nitride ceramic (Si3N4) have been performed with a view to using it for the entire internal wall surface of the swirl chamber. The strength characteristics of Si3N4 and their effect and variation have been determined. On the basis of measurements and analyses of thermal stresses, assembling stresses, etc., investigation of the most suitable construction and assembling methods to reduce load stresses on ceramic, and various kinds of duration tests, the swirl chamber has been confirmed to have the required durability. This engine was found to comply with the 1987 U.S. diesel particulate regulation.

The sequential fuel injection, in which fuel is injected into swirl being generated for mixture stratification, was used to pursue the potential of a lean burn engine for its performance improvement. As a result, it has been found that the most effective method to increase thermal efficiency while reducing NOx emission level is to combine a high-compression compact combustion chamber located on exhaust valve side in cylinder head with DICS (Dual induction Control System). This method was used to build a high-compression lean burn concept vehicle, which was evaluated for compliance to various emission standards. Testing showed that the concept vehicle can improve fuel economy by 10.5% on the Japanese 10-mode cycle, by 8.3% on the ECE mode cycle, and by 6.3% on the U.S. EPA test mode cycle while meeting respective emission standards.

For the purpose of satisfying today's market demands, new 8 and 11 liter diesel engines, named "STORM" series, have been developed and moved into production in 1986. Based on the predecessors which have been produced since 1975, the development of the STORM series aimed high performance, low emission, long life-time and low operating costs. In order to consult customers' convenience, exchangeability of engine parts and commonality of vehicle installations with the former engines had to be maintained. This paper describes the development work of STORM engines, and the design aspects and performance characteristics of these engines.

CORRELATION OF BENDING STRENGTH AND ERRORS OF HELICAL GEAR has not been clarified sufficiently even now. As the investigation by using only experimental method is not sufficient and so the analytical method of obtaining gear bending strength has been developed by one of the authors. Hence, the correlation of bending strength and errors, especially in the aspect of the direction of pressure angle error and tooth trace error, is clarified by this analytical method which was verified by some experiments. And by further investigations, it is confirmed that the helical gear is tougher against the negative pressure angle error, and the fine module gear is sensitive against the errors.